Just nu i M3-nätverket
Gå till innehåll

BIOS Error


Bengt Lundström

Rekommendera Poster

Bengt Lundström

Kan någon hjälpa mig?

Jag skulle uppgradera mitt BIOS, men binfilen var korrupt, så nu går det inte att komma in i datorn.

Hur får jag diskettstationen att gå? Så jag kommer in i datorn och kan flasha med mitt tidigare bios, abit har en felaktig binfil att ladda ner PV heter den. Senaste uppgraderingen. Någon därute hjälp!!! Jag har abit Be6

Länk till kommentar
Dela på andra webbplatser

Det kommer inte att fungera. Du nollar inte bios när du tar bort batteriet, du bara raderar inställningarna.

 

Testa detta istället saxat från en engelsk sida:Återskapa BIOS

 

Solution 1: Boot-block BIOS

Modern motherboards based on Award BIOS have a boot-block BIOS. This is small area of the BIOS that doesn't get overwritten when you flash a BIOS. The boot-block BIOS only has support for the floppy drive. If you have a PCI video card you won't see anything on the screen because the boot-block BIOS only supports an ISA videocard.

The boot-block BIOS will execute an AUTOEXEC.BAT file on a bootable diskette. Copy an Award flasher & the correct BIOS *.bin file on the floppy and execute it automaticly by putting awdflash *.bin in the AUTOEXEC.BAT file.

Solution 2: Get a new BIOS chip.

1. Contact your motherboard manufacturer to see if they sell BIOS chips. Some motherboard manufacturers give them for free.

2. Contact a company that sells pre-flashed chips, like Unicore Software or Midco Computers (formerly RC Systems). Note: We do NOT recommend or endorse this company. There have been too many complaints for soupy's taste. Here's a note from Liz B. at Midco:

"We offer replacement bios chips to the public. We will honor any outstanding orders with RC Systems as we have taken over their domain and are now a new company. Please contact us at www.midcocomputers.com and we will be happy to serve you. "

Solution 3: Hot-swapping:

Note: I'm not responsible for any damage this method may do to you or your computer !

1. Replace the corrupt chip by a working one. The best option is to take the working BIOS chip from a motherboard which has the same chipset although that's not absolutely necessary. It just has to give you a chance of booting into DOS. Before pulling the working BIOS chip out of it's original motherboard, set the System BIOS cacheable option in the BIOS to enabled.

2. After you have put the working BIOS in the motherboard with the corrupt BIOS boot the system to DOS (with a floppy or HD).

3. Now replace (while the computer is powered on) the working BIOS chip with the corrupt one.

4. Flash an appropriate BIOS to the corrupt BIOS and reboot.

Note: Use a flasher from MRBIOS. They are known to work best. You can find them at ftp://ftp.mrbios.com

Solution 3: (for Intel motherboards)

1. Change Flash Recovery jumper to the recovery mode position (not all products have this feature)

2. Install the bootable upgrade diskette into drive A:

3. Reboot the system

4. Because of the small amount of code available in the non-erasable boot block area, no video is available to direct the procedure. The procedure can be monitored by listening to the speaker and looking at the floppy drive LED. When the system beeps and the floppy drive LED is lit, the system is copying the recovery code into the FLASH device. As soon as the drive LED goes off, the recovery is complete.

5. Turn the system off

6. Change the Flash Recovery jumper back to the default position

7. Leave the upgrade floppy in drive A: and turn the system on

8. Continue with the original upgrade

 

 

 

 

Länk till kommentar
Dela på andra webbplatser

Julian Shabo

Man vill ju ta bort inställningarna som gör datorn problematisk, och en borttagning av batteriet gör precis detta. Saxning är lite osäker.

Länk till kommentar
Dela på andra webbplatser

Arkiverat

Det här ämnet är nu arkiverat och är stängt för ytterligare svar.



×
×
  • Skapa nytt...